MQ300PC5H power supply for 5 V LED display loads
The Rong-Electric MQ300PC5H supplies a nominal 5 V DC output for LED display systems. Its documented output range is 0–60 A, with a 300 W rating, output current limiting and short-circuit protection.
Plan the load using the model-specific input and temperature curves. Full output is not specified across every input-voltage and temperature combination. The PDF input section explicitly states AC, although its summary-table heading says Vdc; its temperature graph also extends beyond the environmental-table limit. These source differences are identified below without expanding the stated rating.
Technical specifications
| Parameter | Specification |
|---|---|
| Model | Rong-Electric MQ300PC5H |
| Rated output | 5.0 V DC; 0–60 A; 300 W |
| Input range and frequency | 160–264 V AC, 50/60 Hz (PDF section 5.1); the summary table labels the range Vdc |
| Input-voltage derating | Curve: 80% load at 160 V AC, 90% at 170 V AC, 100% from 180–264 V AC |
| Output-voltage range | 4.90–5.1 V DC |
| Overall regulation | ±2% |
| Voltage / load regulation | ±1% / ±1% |
| Ripple and noise | ≤200 mVp-p at full load; 20 MHz bandwidth with 0.10 µF ceramic and 10 µF electrolytic capacitors at the output |
| Efficiency | ≥88% at 220 V AC, full load and room temperature |
| Power factor | ≥0.95 at full load |
| Maximum input / inrush current | ≤4.0 A / ≤60 A |
| Turn-on delay / rise time | ≤2,500 ms / ≤100 ms |
| Hold-up time | ≥10 ms at 220 V AC |
| Overcurrent protection | 72–90 A threshold; hiccup mode with automatic recovery |
| Short-circuit protection | Supported |
| Working temperature | −30°C to +60°C in the environmental table; apply the derating curve |
| Temperature derating | Curve: 100% through 50°C, 75% at 60°C; the graph extends to 70°C beyond the environmental-table limit |
| Working humidity | 10–90%, non-condensing |
| Cooling | Natural cooling / ventilation, as specified in the environmental table |
| Dimensions / unit weight | 190 × 83 × 29.5 mm / 600 g |
| Input terminals CON1 | Five pins: N, N, L, L, earth; viewed facing the connector from left to right |
| Output terminals CON2 | Six pins: GND, GND, GND, +5 V, +5 V, +5 V; viewed facing the connector from left to right |
| Connector specification | 9.6 mm pitch; input and output connector models rated 300 V, 20 A |
| Source | MQ300PC5H approval specification V1.0, 2020-05-20 |
Product images and specification download

Rong-Electric MQ300PC5H 5V 60A 300W Power Supply for led video wall Specification
Frequently asked questions
Can MQ300PC5H run from a 110 V AC supply?
The model-specific input table gives 160–264 V AC at 50/60 Hz, so 110 V AC is outside the documented range. The summary table uses a Vdc label, but section 5.1, input-frequency entry and derating graph explicitly specify AC.
Is the full 300 W available at 160 V AC?
No. The input-voltage curve specifies 80% load at 160 V AC, 90% at 170 V AC and 100% from 180 V AC upward. Temperature derating and the actual cabinet conditions must also be considered.
Does it deliver full output at 60°C?
The temperature curve falls from 100% at 50°C to 75% at 60°C. The environmental table limits operation to +60°C even though the graph continues to 70°C; do not use that graph extension alone to claim an approved +70°C operating range.
How are the AC and DC terminals arranged?
Facing the connectors from left to right, the PDF defines CON1 as N, N, L, L and earth; CON2 is three GND terminals followed by three +5 V terminals. Verify the markings on the actual unit and follow the connector diagram for installation.
Does the 72–90 A protection threshold increase the 60 A rating?
No. 0–60 A is the specified output-current range. The 72–90 A figure is the overcurrent-protection threshold, with hiccup and automatic recovery, not an additional continuous output rating.




Reviews
There are no reviews yet.