NovaStar MRV560-1 EMC LED Receiving Card | Top Male Hub
$ 35.50
The NovaStar MRV560-1 is the MRV560 series receiving card with male connectors on the top side. The series supports 16-group RGBR′, 20-group RGB and 64-group serial data modes, plus calibration-coefficient storage and status monitoring.
10000 in stock
NovaStar MRV560-1 EMC LED receiving card
NovaStar describes the MRV560 series as the EMC version of MRV360, designed to reduce system electromagnetic radiation. The MRV560-1 is the standard variant with male connectors on the top side. Check this suffix when replacing a card, because other MRV560 variants use different connector positions or genders.
Output modes and monitoring
Two 50-pin hub interfaces support three data modes: 16 groups of RGBR′ parallel data, 20 groups of RGB parallel data, or 64 groups of serial data. The specification provides a different output pin table for each mode. In serial mode, each data cable can drive one LED bar independently.
MOM stores calibration coefficients and LED module information. The card supports configuration readback, a pre-stored image, pixel-level brightness and chromaticity calibration, and monitoring of temperature, Ethernet cable communication and supply voltage. A monitoring card can be connected for additional monitoring.
MRV560-1 technical parameters
| Parameter | Specification |
|---|---|
| Listed model | MRV560-1: top-side male connectors |
| Listed resolution | 256 × 226, exactly as stated in Rev1.1.2 |
| Hub interfaces | 2 × 50-pin interfaces |
| Data modes | 16-group RGBR′ parallel; 20-group RGB parallel; 64-group serial |
| Rated voltage | Minimum 3.3 V / typical 5.0 V / maximum 5.5 V |
| Rated current | Minimum 0.33 A / typical 0.5 A / maximum 0.55 A |
| Working temperature | −20 to +70 °C |
| Working humidity | 10–90% |
| Board thickness | Approximately 1.7 mm |
| Overall thickness | Approximately 19 mm, including the board and components on both sides |
| Module information storage | MOM stores calibration coefficients and LED module information |
The linked document lists 256 × 226 without a refresh-rate condition. This value is retained as written; verify the required screen configuration against the supplied card instead of substituting a resolution from another MRV model.
MRV560 connector variants
| Parameter | Specification |
|---|---|
| MRV560-1 | Standard model; male connector on top |
| MRV560-2 | Male connector on bottom |
| MRV560-3 | Female connector on top |
| MRV560-4 | Female connector on bottom |
These entries identify connector arrangements in the specification. They do not establish current stock availability for each variant.
Frequently Asked Questions
What is the difference between MRV560-1 and other MRV560 variants?
MRV560-1 has top-side male connectors. MRV560-2 uses bottom-side male connectors, MRV560-3 top-side female connectors and MRV560-4 bottom-side female connectors.
Which data output modes does MRV560 support?
The series supports 16 groups of RGBR′ parallel data, 20 groups of RGB parallel data, or 64 groups of serial data through two 50-pin interfaces. Use the correct pin table for the selected mode.
What resolution is listed for MRV560-1?
The linked MRV560 Rev1.1.2 specification states 256 × 226. No refresh rate is given with that feature entry; confirm the required cabinet configuration for the supplied card.
What is the MOM interface used for?
MOM stores calibration coefficients and LED module information. The J4 pin definition is retained below and in the downloadable specification.
What can the MRV560-1 monitor?
The documented monitoring functions cover temperature, Ethernet cable communication status and power-supply voltage. A monitoring card can also be connected.
Connector diagram and pin definitions
The original interface diagram and J4, J9 and J10 definitions are retained below. Consult the PDF for the complete JH1/JH2 data-mode pin tables.
J4 definition（MOM interface）:
| GND | 1 | 2 | SPI_CS |
| SPI_CLK | 3 | 4 | SPI_MOSI |
| CODE0 | 5 | 6 | H164_CSD |
| CODE1 | 7 | 8 | H164_CLK |
| CODE2 | 9 | 10 | |
| 11 | 12 | CODE3 | |
| CODE4 | 13 | 14 | |
| 15 | 16 | SPI_MISO | |
| 17 | 18 | ||
| 19 | 20 | GND |
J9 definition（Indicator light Socket）:
| 1 | 2 | 3 | 4 | 5 |
| STA_LED | LED +/3.3V | PWR_LED – | KEY + | KEY -/GND |
J10 definition（Indicator Socket）:
| 1 | 2 | 3 | 4 | 5 | 6 |
| KEY + | KEY – | PWR_LED+ | PWR_LED- | STA_LED+ | STA_LED- |
Specification download
| Weight | 0.35 kg |
|---|
Be the first to review “NovaStar MRV560-1 EMC LED Receiving Card | Top Male Hub”
You must be logged in to post a review.
Will I be charged with customs and taxes?
The prices displayed on our site are tax-free (in US Dollars), which means you may be required to pay import duties and taxes once you receive your order. Import taxes, duties, and related customs fees will be determined by your local customs office when your order arrives at its final destination.
Please note that these additional charges and taxes are your responsibility, and we do not take any responsibility for them. We are not liable for paying or reimbursing any customs duties, taxes, or related fees. For more details on these charges, please contact your local customs office.
Shipping
We can ship to virtually any address in the world. Note that there are restrictions on some products, and some products cannot be shipped to international destinations..
When you place an order, we will estimate shipping and delivery dates for you based on the availability of your items and the shipping options you choose. Depending on the shipping provider you choose, shipping date estimates may appear on the shipping quotes page.
Please also note that the shipping rates for many items we sell are weight-based. The weight of any such item can be found on its detail page. To reflect the policies of the shipping companies we use, all weights will be rounded up to the next full pound..
Returns Policy
You may return most new, unopened items within 30 days of delivery for a full refund. We'll also pay the return shipping costs if the return is a result of our error (you received an incorrect or defective item, etc.)..
You should expect to receive your refund within four weeks of giving your package to the return shipper, however, in many cases you will receive a refund more quickly. This time period includes the transit time for us to receive your return from the shipper (5 to 10 business days), the time it takes us to process your return once we receive it (3 to 5 business days), and the time it takes your bank to process our refund request (5 to 10 business days).
If you need to return an item, simply login to your account, view the order using the "Complete Orders" link under the My Account menu and click the Return Item(s) button. We'll notify you via e-mail of your refund once we've received and processed the returned item..
Related products
Reviews
There are no reviews yet.