NovaStar MRV412-S受信カードの概要
NovaStar MRV412-Sは、12個の標準HUB75Eコネクタと最大24グループの並列RGBデータに対応したLED受信カードです。ディスプレイキャビネット内のLEDモジュールに接続し、ギガビットイーサネット経由で送信カードからデータを受信します。
8ビットビデオソース(60Hz)の場合、PWMドライバIC搭載カードでは最大解像度512×512ピクセル、共通ドライバIC搭載カードでは最大解像度512×384ピクセルとなります。カード選定の際は、モジュールドライバICと筐体構成をご確認ください。
Whole-card loading: The figures below apply to all module outputs on one card together. They are not a separate pixel allowance for each HUB75E connector. These published conditions are for an 8-bit source; confirm the required configuration before using a different source bit depth.
技術仕様
| 製品仕様 | |
|---|---|
| モジュールコネクタ | 12 × 標準 HUB75E |
| 並列RGBデータ | 最大24グループ |
| 最大解像度:PWMドライバIC | 512×512ピクセル、60Hz、8ビットビデオソース |
| 最大解像度:共通ドライバIC | 512×384ピクセル、60Hz、8ビットビデオソース |
| 入力電圧 | DC3.8V~5.5V |
| 定格電流 | 0.4Vで4.2A |
| 定格消費電力 | 1.68 W |
| 動作温度 | −20℃~+70℃ |
| 動作湿度 | 10%RH〜90%RH、結露しない |
| 貯蔵温度 | −40℃~+85℃ |
| 保存湿度 | 0%RH〜95%RH、結露しない |
| 寸法 | X |
| 正味重量 | 受信カード1枚あたり93.5g |
実際の消費電力は、設定、使用状況、および環境条件によって異なります。ピン配置と設置図については、下記の仕様書を参照してください。
How the MRV412-S Connects to Your Cabinet
| インタフェース | 職種 |
|---|---|
| ギガビットイーサネットポート | Connect to a compatible sending card and cascade other receiving cards. Either port can serve as input or output. |
| HUB75Eコネクタ12個 | Connect to LED modules, supporting up to 24 parallel RGB data groups. |
| 電源コネクタ | Connect the DC input supply. The specification permits either power connector to be used. |
| 5-pin LCD connector | Connect a cabinet LCD module for receiving-card status information. |
Size the LED module power separately from the receiving card’s rated 1.68 W. Confirm the DC 3.8–5.5 V input and module wiring against the exact cabinet configuration.
ディスプレイの調整とキャリブレーション
- カラーマネジメントは、Rec.709、DCI-P3、Rec.2020、およびカスタムカラーガマットに対応しています。
- 18ビット以上の解像度により、低輝度時のグレースケール性能が向上します。ピクセルレベルの輝度および色度補正は、NovaStarのキャリブレーションシステムと連携して動作します。
- 暗い線や明るい線を素早く調整することで、目立つ継ぎ目を修正できます。複数バッチ調整機能を使えば、異なる製造バッチのキャビネットやモジュールを揃えるのに役立ちます。
- 個別のRGBガンマ調整には、NovaLCTと、その機能をサポートするコントローラーが必要です。
- 低遅延はデフォルトで有効になっています。受信カード側で1フレームの遅延を実現するには、RAMを内蔵したモジュールドライバICが必要です。
- 3D出力には、3D対応のコントローラーが必要です。90°刻みの回転はサポートされていますが、自由角度回転にはMCTRL R5コントローラーとSmartLCTが必要です。
- 校正係数は、アップロード、読み出し、ハードウェアへの保存、消去が可能で、必要に応じて高速アップロードもサポートされます。
セットアップ、監視、バックアップ
Data group mapping shows where data groups appear within a cabinet. Mapping 2.0 uses different background colors for Ethernet ports and adapts to cabinet resolutions to show controller, port and receiving-card numbers. Its cabinet-resolution mapping supports a minimum of 36 × 20 pixels. The card supports stored images for startup or signal loss, temperature and voltage monitoring, and a cabinet LCD connection. Bit-error detection and Ethernet disconnection detection assist with communication troubleshooting.
Firmware and configuration parameters can be read back to a computer. Reliability functions include loop backup, dual backup of configuration parameters and dual program backup. Loop backup requires primary and backup line connections between the controller and receiving cards. Configuration backup stores parameters in both application and factory areas; dual program backup stores two firmware copies. These backup functions serve different recovery tasks.
Check Before Ordering a Replacement
- Record the exact card model, hardware revision, working firmware and cabinet configuration before removing the original card.
- Match the module driver IC, scan configuration, HUB75E pinout, cabinet pixel layout and 8-bit source loading conditions.
- Check the 91.5 × 144.0 × 19.3 mm dimensions, mounting clearance, power connector and DC supply range.
- Confirm the sending controller and software needed for 3D, independent gamma or free-angle rotation. Similar MRV model names and connector counts alone do not establish replacement compatibility.
Send your cabinet configuration and original card model for MRV412-S selection assistance、または閲覧 NovaStar制御製品.
製品画像と仕様のダウンロード

MRV412-S仕様書V1.0.0(2026年9月18日)をダウンロード(PDF)
よくある質問
MRV412-SにはHUB75Eコネクタがいくつありますか?
12個の標準HUB75Eコネクタを備え、最大24グループの並列RGBデータをサポートします。
MRV412-S受信カード1枚で、どの程度の解像度のデータを読み込めますか?
8ビットのビデオソースで60Hzの場合、PWMドライバICでは512×512ピクセル、一般的なドライバICでは512×384ピクセルが制限となります。ドライバICの種類は仕様の一部であるため、この2つの制限は互換性がありません。
MRV412-Sに必要な電源電圧はどれくらいですか?
入力電圧範囲はDC3.8V~5.5Vです。定格電流は4.2Vで0.4A、定格消費電力は1.68Wです。
MRV412-Sは低遅延と3Dに対応していますか?
はい。受信カード側で1フレームの遅延を実現するには、RAM内蔵のドライバICが必要です。3D出力の場合、コントローラも3Dに対応している必要があります。
MRV412-SはLEDディスプレイの画像を回転させることができますか?
0°、90°、180°、270°の回転に対応しています。その他の角度での回転には、専用のMCTRL R5コントローラーとSmartLCTソフトウェアが必要です。
Is the maximum resolution per card or per HUB75E port?
It is the total maximum for one card across its module outputs. At 60 Hz with an 8-bit source, use 512 × 512 for PWM driver ICs or 512 × 384 for common driver ICs.
Can an MRV412-S replace an MRV412-N without checking the cabinet?
Confirm the exact hardware revision, firmware, module wiring, driver IC, scan configuration, power and mechanical fit first. Similar model names and 12 HUB75E connectors do not establish a direct replacement.




レビュー
口コミはまだありません。