NovaStar NV3210 HUB320F LED Receiving Card
The NovaStar NV3210 is a receiving card with 10 standard HUB320F connectors. It supports up to 40 groups of RGB real-pixel data, 40 groups of 3-LED sub-pixel data or 30 groups of 4-LED sub-pixel data. HDR10/HLG, calibration and module flash management are available for compatible display systems.
Choose the loading limit for your system: Controller family, driver IC type and video source bit depth all affect the maximum resolution. The tables below show the total load of one receiving card at 60 Hz, across its outputs together.
NV3210 Loading Capacity: M3 and COEX
With PWM driver ICs
| Contrôleur | 8-bits | 10-bits | 12-bits |
|---|---|---|---|
| M3 | 512 × 512 | 512 × 384 | 512 × 384 |
| COEX | 512 × 512 | 512 × 512 | 512 × 384 |
With common driver ICs
| Contrôleur | 8-bits | 10-bits | 12-bits |
|---|---|---|---|
| M3 | 512 × 384 | 256 × 384 | 256 × 384 |
| COEX | 512 × 384 | 512 × 384 | 256 × 384 |
For example, a 10-bit source with PWM driver ICs has a 512 × 384 limit with M3 and a 512 × 512 limit with COEX. Ten HUB320F connectors do not provide ten separate maximum-resolution loads. These figures follow the linked specification V1.1.1; confirm the firmware and actual cabinet configuration before installation.
Connectors, Wiring and Cabinet Fit
The Gigabit Ethernet ports connect to a sending card and cascade other receiving cards; either port can act as input or output. The ten HUB320F connectors connect to LED modules. Either power connector can receive the DC supply. The 5-pin LCD connector supports LCD-related functions only with specialized firmware.
Check the module pinout: The PDF provides separate HUB320F definitions for real-pixel/3-LED sub-pixel data and 4-LED sub-pixel data. Line decoding supports A, B and C signals, while D and E are not supported. A similar connector count on another card does not establish wiring or replacement compatibility.
Spécifications matérielles
| Paramètre | Spécifications |
|---|---|
| Module connectors / data groups | 10 × HUB320F; up to 40 real-pixel RGB groups, 40 three-LED sub-pixel groups or 30 four-LED sub-pixel groups |
| Tension d'entrée | CC 3.8 V à 5.5 V |
| Courant nominal / puissance | 0.5 A / 2.5 W |
| Environnement d'exploitation | −20 °C à +70 °C ; 10 % HR à 90 % HR, sans condensation |
| environnement de stockage | −25 °C à +125 °C ; 0 % HR à 95 % HR, sans condensation |
| Dimensions / poids net | 146.0 × 91.5 × 19.2 mm / 99.5 g par carte |
| Signaux de décodage de ligne | A, B and C; D and E are not supported |
Current and power consumption vary with configuration, use and environment. The 2.5 W rating is for the receiving card; account for LED module power separately. Check the PDF mounting drawing and connector clearance against the cabinet.
HDR, étalonnage et réglage de l'image
The NV3210 supports HDR10 and HLG, Rec.709/DCI-P3/Rec.2020 and custom color gamuts, and 18bit+. Pixel-level brightness and chroma calibration works with the NovaStar calibration system. Quick dark/bright-line adjustment and multi-batch brightness adjustment address seams and cabinet differences.
One-frame latency at the receiving-card end requires driver ICs with built-in RAM. 3D output requires a compatible 3D controller. Independent RGB gamma adjustment uses NovaLCT and a supporting controller. Image rotation is available in 90° increments.
Module Flash, Backup and Maintenance
Modules with flash memory support automatic module calibration, flash management and applying calibration coefficients from module flash. Module auto light-up additionally requires dedicated firmware. Confirm these conditions before relying on automatic setup after a module replacement.
Mapping 1.1 identifies controller, Ethernet port and receiving-card numbers. Stored images, temperature and voltage monitoring, bit-error detection, firmware readback and configuration readback support maintenance. Reliability functions include dual NCP backup, loop backup, dual configuration backup and dual program backup. Loop backup requires primary and backup line connections.
Before Ordering or Replacing an NV3210
- Identify the M3 or COEX controller, driver IC type, source bit depth and total cabinet pixel dimensions; select the corresponding loading limit above.
- Record the current card model, hardware revision, firmware and working cabinet configuration before replacement.
- Check the HUB320F pinout, real-pixel or sub-pixel data mode, data-group count and A/B/C line decoding against the modules.
- Confirm the DC input, mounting dimensions and clearances. Check dedicated firmware and module flash requirements for auto light-up or LCD functions.
Send your controller model, module details and cabinet layout for NV3210 compatibility assistance. Vous pouvez également parcourir le Gamme de produits NovaStar for the controller and receiving-card options required by your system.
Image et spécifications du produit (PDF)

Download NV3210 specification V1.1.1 — October 22, 2024 (PDF)
Questions fréquemment posées
Le NV3210 utilise-t-il des connecteurs HUB75E ou HUB320F ?
It uses 10 standard HUB320F connectors. Match the PDF pin definitions, module wiring and data mode before selecting a replacement.
Pourquoi les limites de charge du NV3210 diffèrent-elles entre les versions M3 et COEX ?
The specification provides limits by controller family, driver IC and source bit depth. For a 10-bit source with PWM driver ICs at 60 Hz, the maximum is 512 × 384 with M3 or 512 × 512 with COEX.
Is the maximum resolution per card or per connector?
The loading values are for one receiving card across all outputs together at 60 Hz. Select the correct controller, IC and bit-depth combination; do not multiply the maximum by ten.
Le NV3210 prend-il en charge le HDR ?
Yes. Specification V1.1.1 lists HDR10 and HLG. Select a compatible controller, source and display configuration for the intended HDR workflow.
La fonction d'éclairage automatique du module est-elle disponible avec le firmware standard ?
Module auto light-up requires dedicated firmware and modules with flash memory. LCD-related functions also require specialized firmware.
Quels signaux de décodage de ligne le NV3210 prend-il en charge ?
It supports A, B and C. D and E signals are not supported. Check the PDF pin table for the selected real-pixel or sub-pixel mode.





Avis
Il n'y a pas encore d'avis.