NovaStar MRV408-S:8-HUB75E LED接收卡
The NovaStar MRV408-S is a cabinet-level LED receiving card with 8 standard HUB75E connectors for LED modules. Its Gigabit Ethernet ports connect to a sending card and cascade other receiving cards; either port can act as an input or output. It supports up to 16 parallel RGB data groups and provides calibration, cabinet mapping and communication diagnostics for LED display setup and maintenance.
其負載限制取決於模組驅動IC。對於60Hz的8位元視訊來源,一張卡片使用PWM驅動IC可支援512×512像素,使用普通驅動IC可支援512×384像素。
MRV408-S 技術參數
| 參數 | 價值 |
|---|---|
| HUB75E 連接器 | 8 個標準連接器 |
| 平行 RGB 數據 | 最多 16 組 |
| 採用PWM驅動IC時可達到最高解析度 | 512 × 512,60 Hz,8 位元視訊來源 |
| 使用通用驅動IC可實現最高解析度 | 512 × 384,60 Hz,8 位元視訊來源 |
| 輸入電壓 | 直流 3.8 V 至 5.5 V |
| 額定電流 | 0.4 A在...上4.2 V |
| 額定功耗 | 1.68W¯¯ |
| 工作溫度/濕度 | -20°C 至 +70°C / 10% RH 至 90% RH,無冷凝 |
| 儲存溫度/濕度 | -40°C 至 +85°C / 0% RH 至 95% RH,無冷凝 |
| 尺寸 | 91.6×107.5×19.3毫米 |
| 淨重 | 每張卡片重 73.7 克 |
額定功率為參考值;實際耗電量取決於設定、使用情況和環境條件。請使用連結的規格書查看連接器引腳定義和安裝尺寸。
影像處理和系統要求
- 色彩管理支援 Rec.709、DCI-P3、Rec.2020 和自訂色域。 18 位元以上色彩深度提升了低亮度灰階性能。
- 像素級亮度和色度校準與NovaStar的校準系統搭配使用。快速接縫調整和多批次調整有助於減少模組或機櫃之間的差異。
- 單獨的 RGB 伽瑪調整功能可與 NovaLCT 和配套控制器搭配使用。
- Low latency is enabled by default. Reducing receiving-card latency to one frame requires driver ICs with built-in RAM; this is not an end-to-end system latency guarantee.
- 3D 顯示需要支援 3D 功能的控制器。支援以 90° 為增量進行影像旋轉;自由角度旋轉需要 MCTRL R5 和 SmartLCT。
- 校準係數管理包括上傳、讀取、儲存到硬體和擦除。上傳可在需要時使用加速傳輸。
機櫃安裝和故障診斷
資料組映射顯示了每個組在機櫃中的位置。映射 2.0 可識別控制器、乙太網路連接埠和接收卡;機櫃解析度映射支援最小 36 × 20 像素。儲存影像設定決定了啟動時或輸入訊號或乙太網路連線遺失時顯示的內容。
溫度和電壓監控、機櫃液晶顯示器支援、誤碼偵測和乙太網路斷開偵測功能有助於維護。韌體和配置參數可以讀取回本機。環路備份使用主備份線路連接,而雙重配置備份和雙程序備份則提供恢復選項。
Before Ordering or Replacing a Card
- Match the complete MRV408-S model code, LED module driver IC, scan configuration and HUB75E pin assignment.
- Check the cabinet pixel dimensions against the applicable per-card loading limit. The limit applies to the whole card, not to each HUB75E connector.
- Check mounting space against the dimensional drawing and provide DC 3.8–5.5 V with the correct polarity. The rated 1.68 W describes the receiving card; LED module power must be sized separately.
- Back up the working cabinet configuration and confirm controller, firmware and software support for the required features. A matching connector count alone does not establish replacement compatibility.
瀏覽 NovaStar controllers and receiving cards, 或者 send your module and cabinet details for selection assistance.
Running Indicator Quick Reference
The green running indicator distinguishes several operating states. The red power indicator stays on when power input is normal.
| Green indicator | 意思 |
|---|---|
| 每秒閃爍一次 | Card operation, Ethernet connection and video input are normal. |
| 每3秒閃爍一次 | 乙太網路線連接異常。 |
| Flashes 3 times every 0.5 seconds | The Ethernet connection is normal, but video input is unavailable. |
See the PDF for the backup-program and loop-redundancy indicator states.
產品圖片及PDF規格說明

Download MRV408-S specification V1.0.0 — September 18, 2026 (PDF)
常見問題
MRV408-S 上有多少 LED 模組連接器?
該卡配備 8 個標準 HUB75E 連接器,支援最多 16 組並行 RGB 資料。安裝前,請對照規格檢查模組接腳排列和機櫃接線。
所有 MRV408-S 配置都支援 512 × 512 像素嗎?
No. That maximum applies to a PWM driver IC with an 8-bit video source at 60 Hz. With a common driver IC under the same source conditions, the limit is 512 × 384 pixels. Both limits are per receiving card, not per HUB75E connector.
MRV408-S 的尺寸和輸入電壓是多少?
此卡尺寸為 91.6 × 107.5 × 19.3 毫米,可接受直流 3.8 伏特至 5.5 伏特電壓。其淨重為 73.7 克。
MRV408-S 能否協助定位乙太網路通訊故障?
是的。它支援誤碼偵測、乙太網路線斷開偵測和 Mapping 2.0,有助於識別接收卡位置和線路。此外,它還可以監控溫度和電壓。
如何在 MRV408-S 上顯示測試圖案?
根據說明,斷開乙太網路線,然後按兩次自檢按鈕顯示測試圖案。再次按下按鈕切換圖案。




過去評論
尚未有評論。