如何測試LED顯示晶片的可靠性和光輸出穩定性

Linsn TS921 PCIe 發送卡片前電路板

To test an LED display chip, measure its light output, color and forward voltage before and after a controlled aging run. Use the same measurement current, temperature and optical setup for both readings. Compare each LED with its own starting values and record any devices that went dark or became intermittent.

In this guide, “chip” means the light-emitting die in a display pixel. A supplier may test the bare die or the packaged LED that goes onto the module. Ask which one was tested. A package test also captures changes in its optical material, internal connections and thermal path.

正確連接LED系統的電路

1. Set the LED Life Test Conditions

(1) Define a pass before powering the samples

A pixel can still light up after aging and fail a color or brightness requirement. Define stability in terms you can measure, such as the allowable change in luminous intensity or color coordinates. For reliability, specify what counts as a failure and the operating period over which each sample must meet the requirements.

(2) Specify the electrical and thermal conditions

Use the datasheet for the exact part and color channel. For a scanned display, record peak current, pulse width and duty cycle. Two drive patterns can have the same average current but expose the LED to different peak currents. For temperature, identify the sensor location so that someone repeating the test knows which temperature to reproduce.

LED可靠度測試計畫清單
測試項目需要具體說明什麼如何解讀它
樣本標識LED型號、顏色、封裝、晶圓或生產批次、樣品數量和選擇方法。結果適用於已記錄條件下的抽樣人群。
電應力正向電流、驅動模式,以及(對於脈衝操作)峰值電流、脈衝寬度和占空比。使用特定型號的額定值;僅憑平均電流無法描述脈衝應力。
熱力條件環境溫度、安裝方式、氣流和溫度測量點。環境溫度並非LED結溫。
測試時長已運轉小時數、測量間隔和任何中斷情況。短期篩檢結果並不能有效預測壽命。
驗收標準允許的光學變化、電氣漂移和功能故障,在測試前已達成協議。使用適用的產品規格或認證計劃;沒有統一的合格標準。

(3) Choose a duration that answers the test question

A burn-in run can reveal early failures. A qualification test asks whether a defined sample meets agreed limits after a specified exposure. If a supplier quotes a projected lifetime, ask for the measured hours, the performance endpoint and the method used to extrapolate from the measurements.

LED測試儀原理圖

2. Measure LED Performance Before and After Aging

(1) Select and identify the samples

For an incoming shipment, select devices from the production lots you intend to accept. For a wafer study, record where on the wafer each die came from. Give every sample a fixture position and an ID. Record any defects found at inspection, even if only initially conforming devices will enter the aging run.

(2) Measure light output, color and forward voltage

Take baseline readings, repeat them at the planned intervals, and let the devices settle at the specified measurement temperature each time. For an RGB package, record red, green and blue separately. A white pixel can change tint when one channel loses output faster than the other two.

If you measure luminous intensity in candelas, fix the viewing angle and distance. A small tilt can change the reading for a narrow-beam LED. If you measure total luminous flux in lumens, use flux again for the final reading. The two quantities describe different aspects of the emitted light.

LED測試儀原理圖

記錄LED老化前後各項測量數據
測量Record比較規則
光輸出初始和後續的光通量,或固定角度下的光強度。始終使用相同的光學量和測量幾何形狀。
正向電壓在規定的測量電流和溫度下測得的電壓。將每個樣本與其自身的基線進行比較;調查意外的漂移。
顏色一致性與 LED 類型相關的顏色座標或主波長。使用相同的儀器設定和約定的顏色限制。
功能性故障開路、短路、間歇性輸出和偵測時間。報告中應保留失敗樣本,而不是只對存活樣本進行平均。
測試條件電流、溫度、中斷、儀器識別和校準狀態。將夾具或測量方法的變化與設備實際性能下降區分開來。

Light output retention (%) = final output ÷ initial output × 100. For example, an LED that measured 10.0 mcd initially and 9.2 mcd after aging retained 92% of its initial intensity. Report the measurement interval alongside that figure. List failed devices separately so a strong average among survivors cannot hide a failure.

(3) Check the package when output falls

When light output drops, first repeat the reading at the original alignment and temperature. Then examine the package for discoloration or other visible changes. An encapsulant that transmits less light can lower the reading even while the die emits light. Record any sunlight or ultraviolet exposure if the samples were evaluated for outdoor service.

(4) Investigate assembly-related failures

Group unusual results by lot and fixture position. If several outliers occupy one part of the bench, check the local temperature and channel current before attributing the pattern to the LEDs. Keep failed parts for inspection. Die attachment, wire bonds and mounting can each affect the result, and some defects require analysis beyond a visual inspection.

3. Set Up and Check the LED Life Test Bench

(1) Verify the current in each branch

LEDs connected in series carry the same current. Parallel strings can draw different currents because their forward voltages differ. Use branch current regulation or a verified balancing circuit, then measure each branch with the fixture populated. Check that the supply can cover the combined forward voltage of a string plus the voltage its current regulator needs.

LM317恆定電流驅動電路原理圖

For the LM317 circuit shown above, check the regulator’s voltage headroom and heat dissipation at the intended string current. Select component values for the LED under test.

(2) Trace a dark string to the failed position

One open connection can extinguish a whole series string. Check the supply and fixture connections, then isolate the suspect device. With a shorted LED, one position can stay dark while current still flows through the others. Record which sample failed and how long its neighbors were without current.

(3) Review the bench log and supplier report

Use powered hours from the log. A fixture shut down for a weekend adds elapsed time without adding operating exposure. Check the sample IDs against the report and look for missing final readings, substitutions or exclusions before accepting the reported pass count.

科銳LED XLamp LED可靠性概述 lists different test conditions and failure criteria for different product groups. Its Long-Term Lumen Maintenance document distinguishes measured output from projected maintenance life. For a display pixel, use the qualification plan for that pixel’s own part number.

有關顯示等級的相關檢查,請閱讀我們的LED 顯示器亮度測量和驗證指南。

4.常見問題解答

(1) Can I test an LED display chip with a multimeter?

A meter in diode-test mode can help check polarity and forward conduction if its test voltage is sufficient for the LED. Some meters cannot light a blue or green LED. A single reading gives no measurement of light loss or color drift over time.

(2) What does a 96-hour LED burn-in test prove?

It tells you how the tested samples behaved during those 96 hours at the stated current and temperature. If a report says only “passed,” ask how many LEDs entered the test, how many failed and whether light output was measured. Those details determine what the result supports.

(3) What current should I use for an RGB display LED?

Identify the part number, the color channel and whether the test uses continuous or pulsed drive. Use a test point supported by the datasheet and qualification plan. A peak pulse rating applies only under its stated pulse conditions.

(4) Why does an LED look dimmer after it warms up?

Light output can change with junction temperature. Allow the device to return to the baseline measurement conditions and remeasure it at the same current. Any remaining difference warrants checking the optical setup and the sample for lasting changes.

(5) Does a passing LED chip test cover the whole screen?

No. Module solder joints, driver electronics, power distribution and cooling introduce other failure points. Check the assembled screen under its intended scan and brightness settings, including solid red, green and blue patterns to reveal missing or uneven pixels.

5. 結論

A useful reliability report lets you follow one LED from its first reading to its last. Look for its part and lot, drive conditions, powered hours, initial and final optical readings, and any recorded failure. If a supplier gives only a lifetime figure or an average brightness value, ask for the underlying sample results before using that figure to qualify a display module.

發表評論