NovaStar NV3210 HUB320F LED Receiving Card
The NovaStar NV3210 is a receiving card with 10 standard HUB320F connectors. It supports up to 40 groups of RGB real-pixel data, 40 groups of 3-LED sub-pixel data or 30 groups of 4-LED sub-pixel data. HDR10/HLG, calibration and module flash management are available for compatible display systems.
Choose the loading limit for your system: Controller family, driver IC type and video source bit depth all affect the maximum resolution. The tables below show the total load of one receiving card at 60 Hz, across its outputs together.
NV3210 Loading Capacity: M3 and COEX
With PWM driver ICs
| 控制器 | 8-位 | 10-位 | 12-位 |
|---|---|---|---|
| M3 | 512×512 | 512×384 | 512×384 |
| COEX | 512×512 | 512×512 | 512×384 |
With common driver ICs
| 控制器 | 8-位 | 10-位 | 12-位 |
|---|---|---|---|
| M3 | 512×384 | 256×384 | 256×384 |
| COEX | 512×384 | 512×384 | 256×384 |
For example, a 10-bit source with PWM driver ICs has a 512 × 384 limit with M3 and a 512 × 512 limit with COEX. Ten HUB320F connectors do not provide ten separate maximum-resolution loads. These figures follow the linked specification V1.1.1; confirm the firmware and actual cabinet configuration before installation.
Connectors, Wiring and Cabinet Fit
The Gigabit Ethernet ports connect to a sending card and cascade other receiving cards; either port can act as input or output. The ten HUB320F connectors connect to LED modules. Either power connector can receive the DC supply. The 5-pin LCD connector supports LCD-related functions only with specialized firmware.
Check the module pinout: The PDF provides separate HUB320F definitions for real-pixel/3-LED sub-pixel data and 4-LED sub-pixel data. Line decoding supports A, B and C signals, while D and E are not supported. A similar connector count on another card does not establish wiring or replacement compatibility.
硬件規格
| 參數 | 規格 |
|---|---|
| Module connectors / data groups | 10 × HUB320F; up to 40 real-pixel RGB groups, 40 three-LED sub-pixel groups or 30 four-LED sub-pixel groups |
| 輸入電壓 | 直流 3.8 V 至 5.5 V |
| 額定電流/功率 | 0.5 安 / 2.5 瓦 |
| 經營環境 | -20°C 至 +70°C;10% RH 至 90% RH,無冷凝 |
| 存儲環境 | -25°C 至 +125°C;0% RH 至 95% RH,無冷凝 |
| 尺寸/淨重 | 卡片尺寸:146.0 × 91.5 × 19.2 毫米 / 每張卡片重量:99.5 克 |
| 線路解碼訊號 | A, B and C; D and E are not supported |
Current and power consumption vary with configuration, use and environment. The 2.5 W rating is for the receiving card; account for LED module power separately. Check the PDF mounting drawing and connector clearance against the cabinet.
HDR、校準和影像調整
The NV3210 supports HDR10 and HLG, Rec.709/DCI-P3/Rec.2020 and custom color gamuts, and 18bit+. Pixel-level brightness and chroma calibration works with the NovaStar calibration system. Quick dark/bright-line adjustment and multi-batch brightness adjustment address seams and cabinet differences.
One-frame latency at the receiving-card end requires driver ICs with built-in RAM. 3D output requires a compatible 3D controller. Independent RGB gamma adjustment uses NovaLCT and a supporting controller. Image rotation is available in 90° increments.
Module Flash, Backup and Maintenance
Modules with flash memory support automatic module calibration, flash management and applying calibration coefficients from module flash. Module auto light-up additionally requires dedicated firmware. Confirm these conditions before relying on automatic setup after a module replacement.
Mapping 1.1 identifies controller, Ethernet port and receiving-card numbers. Stored images, temperature and voltage monitoring, bit-error detection, firmware readback and configuration readback support maintenance. Reliability functions include dual NCP backup, loop backup, dual configuration backup and dual program backup. Loop backup requires primary and backup line connections.
Before Ordering or Replacing an NV3210
- Identify the M3 or COEX controller, driver IC type, source bit depth and total cabinet pixel dimensions; select the corresponding loading limit above.
- Record the current card model, hardware revision, firmware and working cabinet configuration before replacement.
- Check the HUB320F pinout, real-pixel or sub-pixel data mode, data-group count and A/B/C line decoding against the modules.
- Confirm the DC input, mounting dimensions and clearances. Check dedicated firmware and module flash requirements for auto light-up or LCD functions.
Send your controller model, module details and cabinet layout for NV3210 compatibility assistance您也可以瀏覽 NovaStar產品系列 for the controller and receiving-card options required by your system.
產品圖片和規格 PDF

Download NV3210 specification V1.1.1 — October 22, 2024 (PDF)
常見問題
NV3210 使用的是 HUB75E 還是 HUB320F 連接器?
It uses 10 standard HUB320F connectors. Match the PDF pin definitions, module wiring and data mode before selecting a replacement.
為什麼M3和COEX的NV3210裝載限制不同?
The specification provides limits by controller family, driver IC and source bit depth. For a 10-bit source with PWM driver ICs at 60 Hz, the maximum is 512 × 384 with M3 or 512 × 512 with COEX.
Is the maximum resolution per card or per connector?
The loading values are for one receiving card across all outputs together at 60 Hz. Select the correct controller, IC and bit-depth combination; do not multiply the maximum by ten.
NV3210支援HDR嗎?
Yes. Specification V1.1.1 lists HDR10 and HLG. Select a compatible controller, source and display configuration for the intended HDR workflow.
標準韌體是否支援模組自動點亮功能?
Module auto light-up requires dedicated firmware and modules with flash memory. LCD-related functions also require specialized firmware.
NV3210 支援哪些線路解碼訊號?
It supports A, B and C. D and E signals are not supported. Check the PDF pin table for the selected real-pixel or sub-pixel mode.





過去評論
尚未有評論。