LED 디스플레이 칩의 신뢰성 및 광 출력 안정성 테스트 방법

Linsn TS921 PCIe 송신 카드 전면 회로 기판

To test an LED display chip, measure its light output, color and forward voltage before and after a controlled aging run. Use the same measurement current, temperature and optical setup for both readings. Compare each LED with its own starting values and record any devices that went dark or became intermittent.

In this guide, “chip” means the light-emitting die in a display pixel. A supplier may test the bare die or the packaged LED that goes onto the module. Ask which one was tested. A package test also captures changes in its optical material, internal connections and thermal path.

LED 시스템의 회로를 올바르게 연결하십시오

1. Set the LED Life Test Conditions

(1) Define a pass before powering the samples

A pixel can still light up after aging and fail a color or brightness requirement. Define stability in terms you can measure, such as the allowable change in luminous intensity or color coordinates. For reliability, specify what counts as a failure and the operating period over which each sample must meet the requirements.

(2) Specify the electrical and thermal conditions

Use the datasheet for the exact part and color channel. For a scanned display, record peak current, pulse width and duty cycle. Two drive patterns can have the same average current but expose the LED to different peak currents. For temperature, identify the sensor location so that someone repeating the test knows which temperature to reproduce.

LED 신뢰성 테스트 계획 체크리스트
시험 항목무엇을 명시해야 할까요?어떻게 해석해야 할까요?
샘플 식별LED 모델, 색상, 패키지, 웨이퍼 또는 생산 로트, 샘플 수량 및 선정 방법.결과는 명시된 조건 하에서 표본 집단에 적용됩니다.
전기적 스트레스순방향 전류, 구동 모드, 그리고 펄스 작동의 경우 피크 전류, 펄스 폭 및 듀티 사이클.모델별 정격 용량을 사용하십시오. 평균 전류만으로는 순간적인 부하 스트레스를 설명할 수 없습니다.
열 조건주변 온도, 설치 위치, 공기 흐름 및 온도 측정 지점.주변 온도는 LED 접합부 온도와 다릅니다.
테스트 기간운영 시간 경과, 측정 간격 및 모든 중단 사항.단기 검진으로는 수명 예측을 정확하게 할 수 없습니다.
허용 기준시험 전에 합의된 광학적 변화, 전기적 드리프트 및 기능적 고장은 허용됩니다.해당 제품 사양 또는 인증 계획을 사용하십시오. 보편적인 합격 기준은 없습니다.

(3) Choose a duration that answers the test question

A burn-in run can reveal early failures. A qualification test asks whether a defined sample meets agreed limits after a specified exposure. If a supplier quotes a projected lifetime, ask for the measured hours, the performance endpoint and the method used to extrapolate from the measurements.

LED테스터 회로도

2. Measure LED Performance Before and After Aging

(1) Select and identify the samples

For an incoming shipment, select devices from the production lots you intend to accept. For a wafer study, record where on the wafer each die came from. Give every sample a fixture position and an ID. Record any defects found at inspection, even if only initially conforming devices will enter the aging run.

(2) Measure light output, color and forward voltage

Take baseline readings, repeat them at the planned intervals, and let the devices settle at the specified measurement temperature each time. For an RGB package, record red, green and blue separately. A white pixel can change tint when one channel loses output faster than the other two.

If you measure luminous intensity in candelas, fix the viewing angle and distance. A small tilt can change the reading for a narrow-beam LED. If you measure total luminous flux in lumens, use flux again for the final reading. The two quantities describe different aspects of the emitted light.

LED 테스터 회로도

LED 노화 전후를 기록하기 위한 측정
측량기록비교 규칙
광학 출력초기 및 후기 광속, 또는 고정된 각도에서의 광도.전체 과정에서 동일한 광학량과 측정 기하학을 사용하십시오.
순방향 전압지정된 측정 전류 및 온도에서의 전압.각 샘플을 자체 기준선과 비교하고 예상치 못한 편차를 조사하십시오.
색상 일관성LED 유형에 따라 색 좌표 또는 주 파장을 표시합니다.동일한 기기 설정과 합의된 색상 제한을 사용하십시오.
기능적 실패개방 회로, 단락 회로, 간헐적 출력 및 감지 시간.실패한 샘플도 보고서에 포함시키고, 성공한 샘플만 평균내세요.
시험 조건전류, 온도, 정전, 장비 식별 정보 및 교정 상태.고정 장치 또는 측정값의 변화와 실제 장치 성능 저하를 구분하십시오.

Light output retention (%) = final output ÷ initial output × 100. For example, an LED that measured 10.0 mcd initially and 9.2 mcd after aging retained 92% of its initial intensity. Report the measurement interval alongside that figure. List failed devices separately so a strong average among survivors cannot hide a failure.

(3) Check the package when output falls

When light output drops, first repeat the reading at the original alignment and temperature. Then examine the package for discoloration or other visible changes. An encapsulant that transmits less light can lower the reading even while the die emits light. Record any sunlight or ultraviolet exposure if the samples were evaluated for outdoor service.

(4) Investigate assembly-related failures

Group unusual results by lot and fixture position. If several outliers occupy one part of the bench, check the local temperature and channel current before attributing the pattern to the LEDs. Keep failed parts for inspection. Die attachment, wire bonds and mounting can each affect the result, and some defects require analysis beyond a visual inspection.

3. Set Up and Check the LED Life Test Bench

(1) Verify the current in each branch

LEDs connected in series carry the same current. Parallel strings can draw different currents because their forward voltages differ. Use branch current regulation or a verified balancing circuit, then measure each branch with the fixture populated. Check that the supply can cover the combined forward voltage of a string plus the voltage its current regulator needs.

LM317 정전류 구동 회로도

For the LM317 circuit shown above, check the regulator’s voltage headroom and heat dissipation at the intended string current. Select component values for the LED under test.

(2) Trace a dark string to the failed position

One open connection can extinguish a whole series string. Check the supply and fixture connections, then isolate the suspect device. With a shorted LED, one position can stay dark while current still flows through the others. Record which sample failed and how long its neighbors were without current.

(3) Review the bench log and supplier report

Use powered hours from the log. A fixture shut down for a weekend adds elapsed time without adding operating exposure. Check the sample IDs against the report and look for missing final readings, substitutions or exclusions before accepting the reported pass count.

크리 LED XLamp LED 신뢰성 개요 lists different test conditions and failure criteria for different product groups. Its Long-Term Lumen Maintenance document distinguishes measured output from projected maintenance life. For a display pixel, use the qualification plan for that pixel’s own part number.

관련 디스플레이 수준 점검에 대해서는 LED 디스플레이 밝기 측정 및 검증 가이드를 참조하십시오.

4. 자주 묻는 질문

(1) Can I test an LED display chip with a multimeter?

A meter in diode-test mode can help check polarity and forward conduction if its test voltage is sufficient for the LED. Some meters cannot light a blue or green LED. A single reading gives no measurement of light loss or color drift over time.

(2) What does a 96-hour LED burn-in test prove?

It tells you how the tested samples behaved during those 96 hours at the stated current and temperature. If a report says only “passed,” ask how many LEDs entered the test, how many failed and whether light output was measured. Those details determine what the result supports.

(3) What current should I use for an RGB display LED?

Identify the part number, the color channel and whether the test uses continuous or pulsed drive. Use a test point supported by the datasheet and qualification plan. A peak pulse rating applies only under its stated pulse conditions.

(4) Why does an LED look dimmer after it warms up?

Light output can change with junction temperature. Allow the device to return to the baseline measurement conditions and remeasure it at the same current. Any remaining difference warrants checking the optical setup and the sample for lasting changes.

(5) Does a passing LED chip test cover the whole screen?

No. Module solder joints, driver electronics, power distribution and cooling introduce other failure points. Check the assembled screen under its intended scan and brightness settings, including solid red, green and blue patterns to reveal missing or uneven pixels.

5. 결론

A useful reliability report lets you follow one LED from its first reading to its last. Look for its part and lot, drive conditions, powered hours, initial and final optical readings, and any recorded failure. If a supplier gives only a lifetime figure or an average brightness value, ask for the underlying sample results before using that figure to qualify a display module.

댓글을 남겨주세요.