NovaStar MRV412-S 수신 카드 개요
NovaStar MRV412-S는 12개의 표준 HUB75E 커넥터와 최대 24개의 병렬 RGB 데이터 그룹을 지원하는 LED 수신 카드입니다. 이 카드는 디스플레이 캐비닛 내부의 LED 모듈에 연결되며 기가비트 이더넷을 통해 송신 카드로부터 데이터를 수신합니다.
8비트 비디오 소스를 60Hz로 사용할 경우, PWM 드라이버 IC를 사용하면 카드당 최대 해상도는 512 × 512 픽셀이고, 일반 드라이버 IC를 사용하면 512 × 384 픽셀입니다. 카드를 선택할 때는 모듈 드라이버 IC와 케이스 구성을 확인하십시오.
Whole-card loading: The figures below apply to all module outputs on one card together. They are not a separate pixel allowance for each HUB75E connector. These published conditions are for an 8-bit source; confirm the required configuration before using a different source bit depth.
기술 사양
| 매개 변수 | 스펙 |
|---|---|
| 모듈 커넥터 | 12 × 표준 HUB75E |
| 병렬 RGB 데이터 | 최대 24 개 그룹 |
| 최대 해상도: PWM 드라이버 IC | 512 × 512 해상도, 60Hz 주사율, 8비트 비디오 소스 |
| 최대 해상도: 공통 드라이버 IC | 512 × 384 해상도, 60Hz 주사율, 8비트 비디오 소스 |
| 입력 전압 | DC 3.8V ~ 5.5V |
| 정격 전류 | 0.4V에서 4.2A |
| 정격 전력 소비 | 1.68 승 |
| 작동 온도 | -20°C ~ +70°C |
| 작동 습도 | 10% RH ~ 90% RH, 비응축 |
| 보관 온도 | -40°C ~ +85°C |
| 보관 습도 | 0% RH ~ 95% RH, 비응축 |
| 크기 | 91.5 144.0 × × 19.3 MM |
| 순 중량 | 수신 카드당 93.5g |
실제 전력 소비량은 설정, 사용 방식 및 주변 환경에 따라 달라집니다. 핀 정의 및 설치 도면은 아래 사양을 참조하십시오.
How the MRV412-S Connects to Your Cabinet
| 인터페이스 | 직위별 |
|---|---|
| 기가비트 이더넷 포트 | Connect to a compatible sending card and cascade other receiving cards. Either port can serve as input or output. |
| 12개의 HUB75E 커넥터 | Connect to LED modules, supporting up to 24 parallel RGB data groups. |
| 전원 커넥터 | Connect the DC input supply. The specification permits either power connector to be used. |
| 5-pin LCD connector | Connect a cabinet LCD module for receiving-card status information. |
Size the LED module power separately from the receiving card’s rated 1.68 W. Confirm the DC 3.8–5.5 V input and module wiring against the exact cabinet configuration.
디스플레이 조정 및 보정
- 색상 관리 기능은 Rec.709, DCI-P3, Rec.2020 및 사용자 지정 색 영역을 지원합니다.
- 18비트 이상 기술은 저조도 환경에서 그레이스케일 성능을 향상시킵니다. 픽셀 단위 밝기 및 색도 보정은 NovaStar의 보정 시스템과 연동됩니다.
- 어둡거나 밝은 선을 빠르게 조정하여 눈에 띄는 이음새를 수정할 수 있으며, 여러 생산 배치 간의 조정을 통해 서로 다른 생산 배치에서 나온 캐비닛이나 모듈을 일치시킬 수 있습니다.
- 개별 RGB 감마 조정을 위해서는 NovaLCT와 해당 기능을 지원하는 컨트롤러가 필요합니다.
- 저지연 기능은 기본적으로 활성화되어 있습니다. 수신 카드 측에서 1프레임 지연을 구현하려면 내장 RAM이 있는 모듈 드라이버 IC가 필요합니다.
- 3D 출력을 위해서는 3D를 지원하는 컨트롤러가 필요합니다. 90° 단위 회전이 지원되며, 자유 각도 회전을 위해서는 MCTRL R5 컨트롤러와 SmartLCT가 필요합니다.
- 교정 계수는 업로드, 읽기, 하드웨어 저장 및 삭제가 가능하며, 필요한 경우 가속 업로드도 지원됩니다.
설정, 모니터링 및 백업
Data group mapping shows where data groups appear within a cabinet. Mapping 2.0 uses different background colors for Ethernet ports and adapts to cabinet resolutions to show controller, port and receiving-card numbers. Its cabinet-resolution mapping supports a minimum of 36 × 20 pixels. The card supports stored images for startup or signal loss, temperature and voltage monitoring, and a cabinet LCD connection. Bit-error detection and Ethernet disconnection detection assist with communication troubleshooting.
Firmware and configuration parameters can be read back to a computer. Reliability functions include loop backup, dual backup of configuration parameters and dual program backup. Loop backup requires primary and backup line connections between the controller and receiving cards. Configuration backup stores parameters in both application and factory areas; dual program backup stores two firmware copies. These backup functions serve different recovery tasks.
Check Before Ordering a Replacement
- Record the exact card model, hardware revision, working firmware and cabinet configuration before removing the original card.
- Match the module driver IC, scan configuration, HUB75E pinout, cabinet pixel layout and 8-bit source loading conditions.
- Check the 91.5 × 144.0 × 19.3 mm dimensions, mounting clearance, power connector and DC supply range.
- Confirm the sending controller and software needed for 3D, independent gamma or free-angle rotation. Similar MRV model names and connector counts alone do not establish replacement compatibility.
Send your cabinet configuration and original card model for MRV412-S selection assistance, 또는 탐색 노바스타 제어 제품.
제품 이미지 및 사양 다운로드

Download MRV412-S specification V1.0.0 — September 18, 2026 (PDF)
자주 묻는 질문
MRV412-S에는 HUB75E 커넥터가 몇 개 있습니까?
이 제품은 12개의 표준 HUB75E 커넥터를 갖추고 있으며 최대 24개의 병렬 RGB 데이터 그룹을 지원합니다.
MRV412-S 수신 카드 하나로 어떤 해상도까지 로드할 수 있나요?
8비트 비디오 소스를 사용하여 60Hz로 재생할 경우, PWM 드라이버 IC를 사용하면 최대 해상도는 512 × 512 픽셀이고, 일반 드라이버 IC를 사용하면 512 × 384 픽셀입니다. 드라이버 IC 종류는 사양에 포함되어 있으므로 두 해상도 제한은 서로 바꿔 사용할 수 없습니다.
MRV412-S는 어떤 전원 전압을 필요로 합니까?
명시된 입력 전압 범위는 DC 3.8V ~ 5.5V입니다. 정격 전류는 4.2V에서 0.4A이며, 정격 소비 전력은 1.68W입니다.
MRV412-S는 저지연 및 3D를 지원합니까?
예. 수신 카드 측에서 프레임 단위의 지연 시간을 줄이려면 내장 RAM이 있는 드라이버 IC가 필요합니다. 3D 출력을 위해서는 컨트롤러도 3D를 지원해야 합니다.
MRV412-S는 LED 디스플레이 이미지를 회전시킬 수 있습니까?
이 제품은 0°, 90°, 180° 및 270° 회전을 지원합니다. 다른 각도로 회전하려면 전용 MCTRL R5 컨트롤러와 SmartLCT 소프트웨어가 필요합니다.
Is the maximum resolution per card or per HUB75E port?
It is the total maximum for one card across its module outputs. At 60 Hz with an 8-bit source, use 512 × 512 for PWM driver ICs or 512 × 384 for common driver ICs.
Can an MRV412-S replace an MRV412-N without checking the cabinet?
Confirm the exact hardware revision, firmware, module wiring, driver IC, scan configuration, power and mechanical fit first. Similar model names and 12 HUB75E connectors do not establish a direct replacement.




후기
리뷰는 아직 없습니다.